Industries · Food & beverage

Custom plastic components for food & beverage processing equipment

PHOTO NEEDED: CDS-machined part for food or beverage equipment (e.g. a star wheel or guide rail), on a plain ground

Replacement and production parts for fillers, cappers, conveyors, mixers and slicers, machined from FDA-compliant and detectable plastics. Made to your drawing, or from the worn part.

Tolerances
±0.002"–±0.005" on critical dimensions
Depending on the plastic
Machining
CNC milling and turning, including complex geometry
One part to production runs

Parts along the line

From the mixer to the case packer

Find the machine, then the part. Open a part to see how we machine it.

  1. Processing

    Mixers, kettles, slicers, grinders and pumps.

    PHOTO NEEDED: CDS-machined processing part, on a plain ground

    We also machine

    Augers, mixing paddles, nozzles, pump components and cutting boards.

  2. Filling & capping

    Rotary and piston fillers, and cappers.

    PHOTO NEEDED: CDS-machined filling & capping part, on a plain ground

    We also machine

    Timing screws, fill plates and cap chuck inserts.

  3. Conveying & transfer

    Conveyors, transfers and accumulation tables.

    PHOTO NEEDED: CDS-machined conveying & transfer part, on a plain ground

    We also machine

    Chain guides.

  4. Packaging

    Cartoners, case packers and labelers.

    PHOTO NEEDED: CDS-machined packaging part, on a plain ground

Why plastic

Why food plants run plastic parts

In place of metal, on the parts that slide, wear and get washed down every shift.

  • Near the product

    Runs without grease

    Low-friction plastics such as UHMW and acetal slide without added lubricant, so there’s no grease near the food.

  • Chain guides and timing screws

    Quieter than metal

    Plastic running against metal is quieter than metal on metal, which helps plants keep line noise down.

  • Washdown areas

    Won’t rust

    Plastics don’t rust or corrode in water, brine or acidic product, and most take on very little water.

  • Sanitation

    Takes repeated cleaning

    Many grades stand up to daily washdowns, CIP/SIP cycles and sanitizers.

  • Moving parts

    Lighter than metal

    Less load on drives and bearings, and change parts that are easier to lift at changeover.

  • One-off and short runs

    No mold or tooling

    Machined from solid stock, so a single part or a new change-part set goes straight to the machine.

Change parts

Change parts for a new container

Star wheels, timing screws, guides and the rest of a format set, machined together so they fit each other and the machine. Worn sets, spare sets and new sizes from your drawings.

Plastics for food plants

Food contact, detection and guards

If the drawing specifies a plastic, we machine to it. If not, we’ll suggest one with your quote.

Applications

Across food & beverage processing

Parts for the equipment in every kind of food and beverage plant.

  • Meat & poultry

    Slicers, grinders, portioners and conveyors.

  • Dairy

    Fillers, cappers, separators and CIP valves.

  • Beverage & bottling

    Rinsers, fillers, cappers and labelers.

  • Bakery & snack

    Dough dividers, sheeters, rollers and conveyors.

  • Confectionery

    Depositors, molding lines and wrappers.

  • Fruit & vegetable

    Washers, sorters, peelers and cutters.

  • Brewing & canning

    Can fillers, seamers and canning lines.

  • Prepared & frozen foods

    Formers, spiral freezers and tray sealers.

FAQ

Questions from food plants

Acetal, UHMW, HDPE, polypropylene, PET, PTFE and PEEK are common, in grades that comply with FDA food-contact rules. USDA- and 3-A Dairy-compliant grades are also available. If the drawing specifies a plastic, we machine to it. If not, we’ll suggest one.

Many food-grade plastics take repeated washdowns, CIP/SIP cycles and sanitizers without breaking down. Resistance depends on the plastic and the chemical, so list your cleaning chemicals with the quote and we’ll suggest a grade to suit them.

Yes. We machine valve seats, nozzles, pistons, plungers, pump components and sanitary fittings for filling lines and CIP/SIP systems.

Yes. Many food and beverage lines run European-built equipment. Send the drawing or the worn part, and we machine it to its metric dimensions.

Why CDS

Why food plants work with CDS

  • Since 1986

    Decades machining parts for food processing and packaging equipment.

  • HACCP-focused materials

    Food-grade and detectable plastics that support contamination control and HACCP programs.

  • Traceability and documentation

    Every part machined in-house in Aurora, Illinois, with full traceability and documentation.

CDS Plastics building, Aurora, Illinois

Evaluating a supplier? See the shop and how we check the work.

Getting a quote

Send the worn part or the drawing

Or photos of the part and the machine it runs on. Our experienced team takes it from there.

Analytics preferences

Choose whether to allow additional analytics. Essential services and basic site statistics stay on.

Essential website servicesAlways on
Page delivery, forms, security checks and your saved preferences.
Basic site statisticsAlways on
Cloudflare measures traffic and page performance without analytics cookies.

Forms work with additional analytics turned off. Privacy policy